1. Why polytunnels pose particular challenges

Strawberries and soft fruits grown under cover

Strawberries grown in polytunnels ripen earlier, remain cleaner and are less susceptible to the weather than those grown in the open. Growing on raised beds offers further advantages: there is no need to change location; the working height is ergonomic and increases picking efficiency; yields and fruit quality are good; and the produce has a longer shelf life. However, this is offset by considerable investment costs of around €15–20 per m². Cultivation only becomes economically viable with target yields of around 7–9 kg per running metre. Losses due to diseases and pests therefore hit the farm particularly hard.

The climate under plastic sheeting promotes diseases

Warm, humid air and little air movement provide ideal conditions for powdery mildew and botrytis (grey mould). In a variety trial on rack cultivation in a polytunnel at the Silberberg Training Centre (Styria), 44 per cent of the ‘Elegance’ crop was affected by powdery mildew, compared with around 15 per cent for ‘Asia’. The choice of variety and good ventilation therefore help determine how often spraying is required.

Pests and beneficial insects

Thrips, spider mites and the cherry fruit fly multiply rapidly under plastic sheeting. Many growers therefore use beneficial insects. Treatments must then be targeted and carried out in a way that protects these beneficial insects.

Limited space, unsuitable equipment

Typical tunnels for rack cultivation have a wall height of around 2.10 m, row spacing of around 1.15 m and rack heights of around 1.40 m. Sprayers and field sprayers used in open fields are often too large for these conditions. Furthermore, they cannot be adapted to ridge or shelving crops. Smaller, compact equipment with three-nozzle forks or vertical booms is required, which can be adjusted to suit the farm’s specific conditions.

Hand-held spraying is imprecise

On many farms, wheelbarrow sprayers, hose lines and spray guns are still used in tunnels. This results in constant variations in walking speed, arm movement and distance from the plant. The consequences are an uneven spray pattern and uneven distribution of the product: some plants receive too much, whilst others are under-treated. This wastes plant protection products, reduces their effectiveness and can increase the risk of resistance.

 

2. What practical plant protection must achieve

A plant protection measure in protected berry fruit cultivation should meet the following criteria:

  • targeted and tailored to the crop
  • efficient and effective
  • user-friendly and beneficial to beneficial organisms
  • environmentally sound and safe
  • high level of safety for consumers

 

Before each application, the user should clarify the following questions:

  • What is the current stage of crop development?
  • Is it a young or mature plantation (plant height, planting density)?
  • Is the crop grown in the open field or under cover?
  • How dense is the foliage (leaf area, canopy density)?
  • Does the spray droplet reach the target area?

 

In addition, the user must select the appropriate product and timing of application, comply with the instructions for use and application regulations (e.g. non-target organism and non-target plant requirements, bee protection), ensure the user’s safety during preparation, filling and application, wear certified protective clothing, and adjust the application method to suit the plant height and foliage density.

3. The correct application technique

Vertical spray booms and triple-nozzle forks

In strawberry cultivation, field sprayers with booms or triple-nozzle forks are usually used, whilst blower-type sprayers are also frequently employed for rack-grown crops and bush berries. Vertical spray booms and nozzle forks are increasingly used in protected berry fruit cultivation and ensure effective application. The following points should be noted:

  • the distance between the nozzles and the crop
  • an even spray pattern
  • a nozzle output that matches the desired application rate
  • the correct nozzles on the boom
  • ensuring that the spray droplets actually hit the plant or the leaf

 

Nozzle spacing and spray angle

Nozzle spacing and spray angle must be suited to the crop and the cultivation method. In vertical booms and sprayers, nozzles with a spray angle of 80° or 90° are usually used. In row crops such as raspberries, blackberries, redcurrants or gooseberries, the distance between these nozzles and the plant should be at least 15–20 cm to ensure an even spray deposit. If this is not possible for structural or cultivation-related reasons, injector nozzles with a spray angle of 110° or 120° can be used.

On a field sprayer with a horizontal boom and a nozzle spacing of 50 cm, 110° or 120° nozzles are used, as these provide good lateral coverage. The boom should be positioned no more than 50 cm above the crop. Even an increase of just 10 cm in height (from 50 to 60 cm) doubles the drift. Flat-spray nozzles are fitted to the boom at an angle of 5–7° so that the spray patterns do not interfere with one another.

For strawberries grown on raised beds, the nozzles should, where possible, be directed at the plants from the side. If they are positioned directly above the plant, more spray solution rolls off the leaves and drips away (application trial by the Plant Protection Service of the LWK NRW).

Nozzle technology

Injector nozzles are recommended. They ensure good droplet adhesion, penetrate the crop, are biologically effective and cause little drift. A distinction is made between:

  1. Short, compact injector nozzles for the lower pressure range
  2. Long injector nozzles for the upper pressure range

The choice of nozzle depends on the standard spraying pressure used on the farm, the forward speed and the required safety distances. The Julius Kühn Institute (www.jki.bund.de) lists approved loss-reducing nozzles and equipment.

4. Calibration, inspection and maintenance

Only equipment that has been tested and is in perfect working order may be used (plant protection equipment inspection, ‘sprayer MOT’). The equipment should also be calibrated before its first use.

 

Measuring nozzle output

  • Slip 25 cm long pieces of tubing (e.g. old bicycle inner tubes) over the nozzles.
  • Spray for one minute at the standard operating pressure and collect the liquid in a measuring cylinder.
  • Read the volume, make a note of it and continue with the next nozzle until all nozzles have been measured.
  • Compare the individual and total output with the nozzle table.

 

Example: An injector nozzle 90-025 delivers around 1 l/min at 3 bar. Deviations of ±15 per cent are considered acceptable. The pressure gauge can also be checked using the nozzle output: if it deviates by more than 0.2 bar, it must be replaced.

 

Check the spray pattern using water-sensitive paper

Water-sensitive paper is attached to leaves or fruit in the crop using clips and marked. The sprayer is then operated as normal using pure water, and the spray pattern is assessed:

 

  • Is there any dripping loss due to excessive water application?
  • Is the leaf wetting sufficient?
  • Does the spray penetrate deep enough into the plant?
  • Are the correct nozzles fitted to the boom?
  • Maintenance and cleaning

 

Clean the suction and pressure filters regularly, maintain the nozzles and clean the equipment inside and out after each use in a manner that is both appropriate and environmentally sound.

5. Die Lösung: Spritzgeräte SPE, KS und AHS von Ebinger

It is precisely to meet these requirements that Ebinger GmbH has developed the SPE, KS and AHS sprayers. They apply plant protection products, plant fortifiers and similar preparations: with a continuously variable electric drive on the DONKEY XL battery-powered work vehicle (SPE), as a trailer with a battery-powered pump (KS) or as a tractor-mounted sprayer with a PTO pump, flushing system and electric control panel (AHS). Thanks to their compact dimensions, all three units can be used in open fields, greenhouses and polytunnels. Their equipment and applications are highly flexible.

In this design and configuration, the units represent a novelty and a significant advancement on previous plant protection equipment. With conventional wheelbarrow sprayers featuring a hose and spray gun, it is virtually impossible to achieve uniform application. As plant protection products are metered per unit area, hand-held equipment always results in a more or less uneven spray pattern.

The SPE, KS and AHS are moved through the crop at a constant speed; in the case of the SPE, this is electrically controlled and continuously variable from 0 to 6 km/h. This ensures that the spray is distributed very precisely and evenly across the area. Two spray booms, each with 3, 4 or 5 nozzles, operate close to the crop. The nozzles can be directed sideways towards the plants, as recommended for trellised crops. All three machines are fitted with an agitator that keeps the spray mixture evenly blended. Compared with the spraying methods previously in use, this results in significant savings in working time.

Which machine for which job?

  • SPE on DONKEY XL: no tractor required, quiet and emission-free, with a steering drawbar, for narrow tunnels and greenhouses. The DONKEY can be used as a transporter outside the spraying season.
  • KS 218 / 236: lightweight battery-powered trailer sprayer (115 kg) for small towing vehicles, 80 cm wide.
  • AHS: PTO-driven trailer sprayer for tractors, with a tank capacity of up to 660 l and a flow rate of 105 l/min, for larger areas and numerous tunnels.

Well suited for

  • Bed crops in greenhouses and the open field, e.g. ornamental plants, nursery stock, perennials, young plants
  • Tall-growing crops in greenhouses, e.g. cucumbers, tomatoes, peppers
  • Protected cultivation in polytunnels, e.g. strawberries on ridges and racks, raspberries

A comparison of SPE, KS and AHS

 

Feature

SPE 200 / 236

KS 218 / 236

AHS

Design

Mounted on DONKEY XL battery-powered utility vehicle

Trailer

Tractor trailer

Mobility

Electric, continuously variable speed 0–6 km/h, electric brake

Towed (towing eye or ball hitch)

Towed, Category I steering drawbar, tandem axle

Spray pump drive

Battery-powered

Battery-powered, charger included

PTO-driven (power take-off)

Flow rate

18 / 36 L/min

18 / 36 L/min

105 L/min, 20 bar

Tank

200 L, width 55 cm

200 L, width 55 cm

220, 330, 440 or 660 L, width 68 cm

Agitation system

Yes

Yes

Yes

Spray boom

2 spray bars, each with 3/4/5 nozzles

2 spray bars, each with 3/4/5 nozzles

2 spray bars, each with 3/4/5 nozzles

Control unit

2 spray sections, manual pressure adjustment

2 spray sections, manual pressure adjustment

Electric control with pressure regulator, 2 spray sections operated via solenoid valves

Height adjustment

Manual, up to 210 cm

Manual, up to 210 cm

Electric, up to 210 cm (450 mm lifting range)

Overall width

78 cm

80 or 100 cm

90 cm

Rinsing system

–

–

40 L rinsing tank, 15 L handwashing tank

Empty weight

290 kg

115 kg

280 kg

Plant protection products may only be applied by persons holding a valid certificate of competence. Observe the authorisation, the instructions for use and the application regulations for the respective product (e.g. NW/NT requirements, bee protection, operator protection) for protected cultivation.


Sources
•    Stuch, M. (LWK NRW): Application in soft fruit cultivation. Spargel & Erdbeer Profi 1/2021, pp. 72–75.
•    Lafer, G.: Raised-bed cultivation of strawberries in polytunnels – variety trials and comparison of planting material. Haidegger Perspektiven 2/2017.
•    Syngenta Agro GmbH: Application techniques for strawberries, www.syngenta.de
•    Obst & Wein Technik: All about protected cultivation (application trial for strawberries on raised beds, R. Jung, LWK NRW), obstwein-technik.eu
•    Julius Kühn Institute: Directory of loss-reducing equipment, www.jki.bund.de